I have 3 TRÅDFRI 30W drivers in my kitchen, and succeeded in pairing all of them to the same remote. However, if I pair a lamp to a 2nd remote, it stops responding to the first one. I was hoping to use 2 remotes, to get 2-way control.

From the documentation, one remote can control 10 lamp drivers, but it isn't clear to me if only one remote can drive a lamp at once. If it's possible, is there a reliable way to set it up?

I don't have a gateway. If I have a gateway, can I use IFTTT to cross connect two driver/remote pairs or subsets to keep the drivers in sync in the way that I could do with SonOff?

  • you answered your own question .... However, if I pair a lamp to a 2nd remote, it stops responding to the first one.
    – jsotola
    Commented Oct 7, 2018 at 20:50
  • 2
    @jsotola, I'm asking if I'm doing something silly, or if the designer has done something monumentally stupid. It's not clear, but I guess from your comment you believe it to be the latter. If you know the designer, maybe you can flag the documentation for an update. Maybe a firmware update would give a different result. Commented Oct 7, 2018 at 21:59
  • I need to source this info "managed to get two Tradfri motion sensors paired with one group of lights (it's unsupported, but discussed openly by Ikea on Reddit) - I do have the gateway but thats not involved: you pair one remote steering device with another." Commented Nov 7, 2018 at 9:31
  • @jsotola Wrong. Simply undocumented and not obvious. Commented Nov 7, 2018 at 20:50
  • none of this worked for me to clone the two remotes. i am using a gateway, not pairing directly to the cabinet lights. after hours of trying, I give up and now this fancy remote is another useless pile of plastic. ive tried at least three different methods including all of those listed here. if anyone has alternative advice, Id be grateful.
    – Betty Soto
    Commented Sep 1, 2022 at 5:35

3 Answers 3


(This is from observation, not documented fact)

I don't believe this is possible, even with a gateway.

In the gateway setup, groups are defined by the remote/dimmer/pir. You pair the controller with the gateway then use it to add lights, there is no way to add a second controller to a group.

Also when I did the work to reverse engineer CoAP protocol I never found a way to get the remote inputs, only notifications about the changes in state of the lights.

I do need to go back and have another low level play with gateway, but it does seem to be a limitation.

  • See below: This seems just plain wrong.
    – Jinxed
    Commented Oct 21, 2023 at 23:44

Yes, there is an easy, but undocumented way to do this.

  1. Factory reset the remotes (press pair 4x within 5 sec).
  2. Pair one remote to a bulb (this may not be necessary, but I did this)
  3. Hold the remotes next to each other, press both pair buttons for 10 sec. LEDs on the front come on, then flicker off.
  4. Observe both remotes control the 1st bulb.
  5. Pair one remote to a 2nd bulb.
  6. Observe both remotes control both bulbs.

From Ikea on Reddit

You can actually clone two of the same input device if you like. It's not documented but if you keep two input devices close to eachother and hold the pairing button on first one, keep holding it and at the same time hold the pairing button on the other one they will both end up in the same group. (You should get feedback from the LEDs) I'd recommend doing a factory reset on the input device you are trying to add into the group before starting the process.

  • oooh, will have to have a play with that. Need to get back to Ikea to get one of the sockets with a switch (have one without which is not that useful...)
    – hardillb
    Commented Nov 7, 2018 at 11:01
  • At least their returns policy is great for prototyping a system. Commented Nov 7, 2018 at 11:36
  • I have tried the extra remote method, was easy and simple to set up. You can set it up without the app but you won't get the firmware updates. Multiple Remotes
    – SK888
    Commented Dec 3, 2018 at 9:38
  • This works perfectly. I even have my Hue bulbs attached to Hue Bridge. The only Ikea hardware here are two switches. Amazing.
    – Vladimir
    Commented Feb 24, 2021 at 16:19
  • I tried pairing 2 remotes I have, an E1524 and an E1810, but it did not work, unfortunately. The lights (which are ~0.5cm above the power icon on the front) never came on when holding the 2 remotes nearby and holding the pair buttons. I wonder if it's because I used a gateway previously, or because the remotes are different, or because I did not reset the switches...
    – citelao
    Commented Aug 30, 2023 at 16:59

Really simple. Just hold down both Remote pair button at the exact same time next to each bulb you want to pair with for 10s. Boom!

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.